MSE024 motor control unit for up to 4 motors

MSE024 motor control unit for up to 4 motors

SKU: 342
GTIN: 4260336110712
Category: Central group controller
Manufacturers: 3T-Motors

Motor group control with time logic and automatic reversing

201,90 €

incl. 19% VAT , plus

Available immediately
Delivery time: 1 - 2 Workdays (DE - int. shipments may differ)

Description
Product safety

Motor Control Unit MSE 024

4-channel group motor control unit with
time logic and reversing automation

For controlling up to 4 roller shutter / awning motors
(230VAC motors with mechanical or electronic end switches)
Mounted in surface-mounted plastic housing (IP55) 240x195x85mm
Control via individual/group switches or through 24 V DC control line from central unit
Please use only switches, not toggle switches!
Important:
No external voltage should be applied to any of the existing switch inputs. The control voltage for the operating elements is provided by the MSE in low voltage. Any connected timers, e.g., at the group switch input, must be potential-free (e.g., Easy Master from Simu).

Features and Functions:

The motor control unit provides high user comfort in decentralized sun protection systems. Up to 4 motors can be controlled either individually or in groups. The integrated power supply provides the necessary supply voltage for the internal electronics, so the MSE can also be used as a group controller without a central unit.
The control is via a 24V DC control line from the central unit or through the individual/group switches. Up to 200 devices can be operated on a single control line without an expansion power supply.
Within a motor control unit, drives can be grouped together using dip switches, and several motor control units of the MSE02X series can be grouped by simply connecting their group control inputs.
The motor control unit can control all common 230VAC motors with mechanical or electronic end switches. Each motor is individually fused (2 AmT).
Time Logic:
Two control programs are available:
e.g., for controlling Venetian blind or shutter motors:
Pressing a local switch for more than 2 seconds in the desired direction triggers a 3-minute pause logic. By sending a control pulse in the opposite direction, the system can be stopped at any intermediate position.
Control pulses shorter than 2 seconds can move the system open or closed as needed.
e.g., for controlling roller shutter or awning motors:
Using dip switch (JP5.1), the pause logic can be set to activate without delay.
A control pulse in the opposite direction will stop the system at any intermediate position.
Reversing Automation:
The reversing automation function causes the slats of the Venetian blinds or shutters to automatically open (view position) after reaching the lower end position.
This reversing pulse in the "retracting" direction is adjustable via dip switches 5.2-5.4 from 0 to 0.7 seconds. The reversing time can be shortened by pressing the manual switch again in the same direction.
Connections for external blind switches per motor and group switch per device
Control mounted in surface-mounted plastic housing IP55 (with housing cover); dimensions 240x195x85mm
Available versions:
MSE 024 for 4 motors in surface-mounted housing 240x195x85 mm
MSG 026 for 6 motors in surface-mounted housing 250x160x90 mm
Made in Germany
2-year warranty

Technical Specifications:
Type:	MSE 024
Control Unit Supply Voltage:	230V / 50Hz
Control Line from Central Unit:	24VDC, polarity is optional
Motor Connections:	230VAC, maximum 2A
Operating Temperature Range:	0°C to +60°C
Motor Fuse:	2 AmT
Protection Rating:	IP55
Dimensions:	240x195x85mm (H x W x D)

Product Video:

WEEE Reg. No.: DE 77028333

Manufacturer/EU Responsible person

3T-Components GmbH & Co. KG
Grete-Schickedanz-Straße 5
55545 Bad Kreuznach
Germany

Phone: 0671 887 673 0
E-mail: info@3t-components.de

General safety instructions

Please read these important safety instructions before commissioning! Incorrect installation can cause serious personal injury and damage to property. Failure to comply with this user information and all instructions and provisions contained herein will invalidate the warranty. If these instructions are not followed, the manufacturer or supplier shall not be liable for any personal injury or damage to property

General safety instructions

Follow all instructions, as incorrect installation can lead to serious injury.

WARNING: The drive must be disconnected from the power source during cleaning, maintenance and when replacing parts
The electrical connection, installation and commissioning of the motor may only be carried out by qualified specialist personnel.
The relevant regulations and guidelines must be followed at all times to prevent damage to persons and property
Assembly and connection of switching devices may only be carried out in a de-energised state
The electrical installation must be carried out in accordance with VDE 0100 or the legal regulations and standards of the respective country by an authorised electrician. This person must observe the enclosed installation instructions for the electrical devices supplied.
No use of defective devices: Never use defective devices
Keep the instructions for future reference

Inappropriate use

Do not allow children to play with the motor controls
Do not use blind switches, these can cause damage to the system and the motors!
If the power cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Proper use

Use the motor group controller only to automate roller shutters, awnings, external venetian blinds or Venetian blinds.
The mains connection cable for the drives must be laid inside the conduit up to the junction box. The local electrical regulations must be observed.
A 230V/50 Hz power connection with fuse must be available at the installation site for the electrical connection of the motor group control unit
Persons must be instructed in the correct operation of the motor group control unit
The roller shutter movement must be monitored so as not to endanger persons

Disposal instructions

Separate collection of old appliances
Electrical and electronic appliances that have become waste are referred to as old appliances. Owners of old appliances must dispose of them separately from unsorted municipal waste. In particular, old appliances do not belong in household waste, but in special collection and return systems.

Possibilities for returning old appliances
Owners of old appliances from private households can hand them in at the collection points of the public waste disposal organisations or at the take-back points set up by manufacturers or distributors in accordance with the ElektroG.

Meaning of the "crossed-out wheelie bin" symbol
The crossed-out wheelie bin symbol regularly displayed on electrical and electronic appliances indicates that the appliance in question must be collected separately from unsorted municipal waste at the end of its service life.