Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Motor control unit MSE026 Time logic for up to 6 motors

Motor control unit MSE026 Time logic for up to 6 motors

SKU: 340
GTIN: 4260336110729
HAN: MSE026
Category: Central group controller
Manufacturers: 3T-Motors

motor group control with time logic and automatic reversing

248,90 €

incl. 19% VAT , plus

Available immediately
Delivery time: 0 Workdays (DE - int. shipments may differ)

Description
Product Safety

Motor Group Control Unit MSE026

6-channel group motor control unit with time logic and reversing automation for controlling up to 6 awning or roller shutter motors

Important Notes:

No external voltage should be applied to any of the existing switch inputs!
The control voltage for the operating elements is provided by the MSE in low voltage. Any timers connected, e.g., at the group switch input, must be potential-free (e.g., Easy Master from Simu).
Use only push buttons, not switches! These can cause damage to the system and motors.

Features and Functions:

The motor control unit provides high user comfort in decentralized sun protection control systems. Up to 6 motors (230 VAC with mechanical or electronic end switches) can be controlled both individually and in groups. The integrated power supply provides the necessary supply voltage for the internal electronics, allowing the MSE to also function as a group controller without a central unit.
The control is via a 24 VDC control line from the central unit or through the individual/group push buttons. Up to 200 devices can be operated on a single control line without an expansion power supply.
Within a motor control unit, drives can be grouped together using dip switches, and multiple motor control units from the MSE02X series can be grouped by simply connecting their group control inputs.
All motors are individually protected with a 2 AmT fuse.
Time Logic:
Two control programs are available:
e.g., for controlling Venetian blind or shutter motors:
Pressing a local switch for more than 2 seconds in the desired direction triggers a 3-minute pause logic.
By sending a control pulse in the opposite direction, the system can be stopped at any intermediate position.
Control pulses shorter than 2 seconds can move the system open or closed as needed.
e.g., for controlling roller shutter or awning motors:
Using dip switch (JP5.1), the pause logic can be set to activate without delay.
A control pulse in the opposite direction will stop the system at any intermediate position.
Reversing Automation:
The reversing automation function causes the slats of the Venetian blinds or shutters to automatically open (view position) after reaching the lower end position. This reversing pulse in the "retract" direction is adjustable via dip switches 5.2 to 5.4 from 0 to 0.7 seconds. The reversing time can be shortened by pressing the manual switch again in the same direction.
connections for external blind switches per motor and group switch per device
the control unit is mounted in a surface-mounted plastic housing IP55 (250x160x90 mm)
available versions:
MSE024 for 4 motors in surface-mounted housing 240x195x85 mm
MSE026 for 6 motors in surface-mounted housing 250x160x90 mm
made in germany: our central control units are manufactured in-house, guaranteeing the highest operational reliability
2-year warranty

Technical Specifications:
Type:	MSE026
Control Unit Supply Voltage:	230 V / 50 Hz
Control Line from Central Unit:	24 VDC, polarity is optional
Motor Connections:	230 VAC, maximum 2 A
Operating Temperature Range:	0°C to +60°C
Motor Fuse:	2.0 AmT
Protection Rating:	IP55
Dimensions (HxWxD):	250x160x90 mm

Product video:

WEEE-Reg. No.: DE 77028333

Item information	Value
Shipping weight:	1,46 kg
Item weight:	1,46 kg

Manufacturer/EU Responsible person

3T-Components GmbH & Co. KG
Grete-Schickedanz-Straße 5
55545 Bad Kreuznach
Germany

Phone: 0671 887 673 0
E-mail: info@3t-components.de

General safety instructions

Please read these important safety instructions before commissioning! Incorrect installation can cause serious personal injury and damage to property. Failure to comply with this user information and all instructions and provisions contained herein will invalidate the warranty. If these instructions are not followed, the manufacturer or supplier shall not be liable for any personal injury or damage to property

General safety instructions

Follow all instructions, as incorrect installation can lead to serious injury.

WARNING: The drive must be disconnected from the power source during cleaning, maintenance and when replacing parts
The electrical connection, installation and commissioning of the motor may only be carried out by qualified specialist personnel.
The relevant regulations and guidelines must be followed at all times to prevent damage to persons and property
Assembly and connection of switching devices may only be carried out in a de-energised state
The electrical installation must be carried out in accordance with VDE 0100 or the legal regulations and standards of the respective country by an authorised electrician. This person must observe the enclosed installation instructions for the electrical devices supplied.
No use of defective devices: Never use defective devices
Keep the instructions for future reference

Inappropriate use

Do not allow children to play with the motor controls
Do not use blind switches, these can cause damage to the system and the motors!
If the power cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Proper use

Use the motor group controller only to automate roller shutters, awnings, external venetian blinds or Venetian blinds.
The mains connection cable for the drives must be laid inside the conduit up to the junction box. The local electrical regulations must be observed.
A 230V/50 Hz power connection with fuse must be available at the installation site for the electrical connection of the motor group control unit
Persons must be instructed in the correct operation of the motor group control unit
The roller shutter movement must be monitored so as not to endanger persons

Disposal instructions

Separate collection of old appliances
Electrical and electronic appliances that have become waste are referred to as old appliances. Owners of old appliances must dispose of them separately from unsorted municipal waste. In particular, old appliances do not belong in household waste, but in special collection and return systems.

Possibilities for returning old appliances
Owners of old appliances from private households can hand them in at the collection points of the public waste disposal organisations or at the take-back points set up by manufacturers or distributors in accordance with the ElektroG.

Meaning of the "crossed-out wheelie bin" symbol
The crossed-out wheelie bin symbol regularly displayed on electrical and electronic appliances indicates that the appliance in question must be collected separately from unsorted municipal waste at the end of its service life.

Others also bought:

MSE024 motor control unit for up to 4 motors

201,90 € *

Flush-mounted cut-off relay TR2-UP

14,25 € *