Cookiename	Beispielinhalt	Ablaufzeit
_ga_*	deleted	730 Tage
_ga	GA1.1.8643343795.1726666186	730 Tage

Flush-mounted cut-off relay TR4-UP

SKU: 97
GTIN: 4260601767948
HAN: TR4-UP
Category: group controller
Manufacturers: 3T-Motors

for controlling 4 roller shutter motors

21,50 €

incl. 19% VAT , plus

Available immediately
Delivery time: 0 Workdays (DE - int. shipments may differ)

Description
Product Safety

In-wall cut-off relay TR4-UP

4-fold cut-off relay for controlling 4 roller shutter motors

Features and functions:

with the TR4-UP, you can combine up to 4 roller shutter motors into a group and control them centrally via a blind push-button
flush-mounted for installation in deep switch box (Ø 60 mm / depth: 66 mm) or surface-mounted moisture-proof junction box
must be used when operating 2 to 4 motors via one push-button
Centralised operation only with blind push-button! Blind switches cause damage to the system
small design, height only 50 mm
2-year guarantee

Technical data:
Type:	TR4-UP
Supply voltage:	230 V, 50 Hz, +-10% Neutral conductor required
Control voltage:	230 V, 50 Hz, +-10%
Current consumption:	10 mA in relay mode
Switching power:	max. 2 A, 250 VAC, Motor load max. 750 VA, Only for 230 V motors with limit switches
Operating temperature range:	0°C to +60°C
Screw terminals:	Solid, 2x1.5 mm², 1x2.5 mm², Flexible 1.5 mm²
Dimensions (HxWxD):	43x50x50 mm
Installation:	In deep switch box (Ø 60 mm / depth: 66 mm) or surface-mounted moisture-proof junction box

Product video:

WEEE-Reg. No.: DE 77028333

Item information	Value
Shipping weight:	0,11 kg
Item weight:	0,09 kg

Manufacturer/EU Responsible person

3T-Components GmbH & Co. KG
Grete-Schickedanz-Straße 5
55545 Bad Kreuznach
Germany

Phone: 0671 887 673 0
E-mail: info@3t-components.de

General safety instructions

Please read these important safety instructions before commissioning! Incorrect installation can cause serious personal injury and damage to property. Failure to comply with this user information and all instructions and provisions contained herein will invalidate the warranty. If these instructions are not followed, the manufacturer or supplier shall not be liable for any personal injury or damage to property

General safety instructions

Follow all instructions, as incorrect installation can lead to serious injury.

WARNING: The drive must be disconnected from the power source during cleaning, maintenance and when replacing parts
The electrical connection, installation and commissioning of the motor may only be carried out by qualified specialist personnel.
The relevant regulations and guidelines must be followed at all times to prevent damage to persons and property
Assembly and connection of switching devices may only be carried out in a de-energised state
The electrical installation must be carried out in accordance with VDE 0100 or the legal regulations and standards of the respective country by an authorised electrician. This person must observe the enclosed installation instructions for the electrical devices supplied.
No use of defective devices: Never use defective devices.
Keep the instructions for future reference.

Inappropriate use

Do not allow children to play with the motor controls
Do not use blind switches, these can cause damage to the system and the motors!
If the power cord of this appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

Proper use

Only use the multiple control unit to automate roller shutters or awnings
The mains connection cable of the drives must be laid inside the conduit up to the junction box. The local electrical regulations must be observed..
A 230V/50 Hz power connection with fuse must be available at the installation site for the electrical connection of the multiple control unit
Persons must be instructed in the correct operation of the motor group control unit.

Disposal instructions

Separate collection of old appliances
Electrical and electronic appliances that have become waste are referred to as old appliances. Owners of old appliances must dispose of them separately from unsorted municipal waste. In particular, old appliances do not belong in household waste, but in special collection and return systems.

Possibilities for returning old appliances
Owners of old appliances from private households can hand them in at the collection points of the public waste disposal authorities or at the take-back centres set up by manufacturers or distributors in accordance with the ElektroG.

Meaning of the "crossed-out wheelie bin" symbol
The crossed-out wheelie bin symbol regularly displayed on electrical and electronic appliances indicates that the appliance in question must be collected separately from unsorted municipal waste at the end of its service life.