3T Wireless Light Sensor LSF

SKU: 816
GTIN: 4260336113386
Category: 3T-Motors radio controls
Manufacturers: 3T-Motors

For sun-dependent control of 3T radio roller shutter motors or 3T radio receivers

48,90 €

incl. 19% VAT , plus

Currently out of stock

3T Wireless Light Sensor LSF

For sun-dependent control of 3T radio roller shutter motors or 3T radio receivers (MFE, UPE1, WEF1, WETF1)

Features and functions:

For roller shutters or internal textile sun blinds (textile screens)
Taught-in via already programmed transmitter of the radio roller shutter motor or radio receiver (for MFE / UPE1)

or directly on the radio receiver (for WEF1 / WETF1)
Sensor can be taught to several radio roller shutter motors / radio receivers
Incl. suction cup for mounting on the inside of the window glass (alternatively double-sided adhesive tape included)
2 operating modes:
Shutter mode: The shutter moves downwards when the sun threshold is exceeded until the sensor is covered. is covered.
The roller shutter then automatically moves up a little so that the sensor can continue to measure the sun intensity. can continue to measure the sun intensity.
Textile sun protection blind mode: The blind moves downwards to the set end position when the sun threshold is exceeded. to the set end position.
The blind must move down behind the sensor so that it is not shaded.

Sensor can be deactivated and activated by pressing a button on the device (set the sun value to "0").
Range approx. 30 m indoors, 200 m outdoors

Technical data:
Type:	LSF
Input voltage:	3 V
Frequency:	433.92 MHz ± 100 KHz
Transmitter power:	10 mW
Operating temperature range:	-20°C to +60°C
Battery type:	3 V / CR2032 (included in the scope of delivery)
Dimensions (LxWxH):	43x43x24 mm (with suction cup)

What's included:

1 pc. 3T wireless light sensor LSF
1 pc. Battery 3 V / CR2032
1 suction cup and double-sided adhesive tape
Comprehensive and easy-to-understand operating instructions

Product video:

WEEE-Reg. No.: DE 77028333

Manufacturer/EU Responsible person

3T-Components GmbH & Co. KG
Grete-Schickedanz-Straße 5
55545 Bad Kreuznach
Germany

E-mail: info@3t-components.de
Phone: 0671 887 673 0

Safety instructions for radio controls

Please read these important safety instructions before commissioning! Incorrect installation and operation can cause serious personal injury and damage to property. Failure to comply with this user information and all instructions and provisions contained therein will invalidate the warranty. If these instructions are not followed, the manufacturer or supplier shall not be liable for any personal injury or damage to property.

General safety instructions

Follow all instructions, as incorrect installation can lead to serious injury.

Make sure to change the batteries of the radio transmitter regularly. Only use the batteries recommended by the manufacturer. Dispose of used batteries in an environmentally friendly manner.

Improper use

Do not use old or damaged batteries. Dispose of defective batteries immediately in accordance with local regulations on battery disposal.

Proper use

Make sure that radio controls are suitable for use with tubular motors and comply with the technical specifications.
Persons must be instructed in the correct operation of the radio control system.
Check regularly that the radio control is working properly.

Disposal instructions

Separate collection of old appliances
Electrical and electronic appliances that have become waste are referred to as old appliances. Owners of old appliances must dispose of them separately from unsorted municipal waste. In particular, old appliances do not belong in household waste, but in special collection and return systems.

Possibilities for returning old appliances
Owners of old appliances from private households can hand them in at the collection points of the public waste disposal authorities or at the take-back centres set up by manufacturers or distributors in accordance with the ElektroG.

Meaning of the "crossed-out wheelie bin" symbol
The symbol of a crossed-out wheelie bin regularly shown on electrical and electronic equipment indicates that the respective device must be collected separately from unsorted municipal waste at the end of its service life.

Battery instructions

Batteries can be returned free of charge to the point of sale after use.

The end user is legally obliged to return used batteries.

At the end of their service life, batteries and accumulators that are no longer usable must not be disposed of with household waste. This is indicated by the crossed-out wheelie bin symbol. The chemical symbols Hg (mercury), Cd (cadmium) or Pb (lead), which may appear below the symbol of the crossed-out wheelie bin, indicate the substances contained.