GEBA ROLLOTIMER ASTRO
For switching roller shutter and blind drives
Colour: ultra white
- Easy to operate: Everything under control with just two buttons
- Daily programme
- Weekly programme
- Holiday programme
- Astro programme
- Sun/twilight programme
- Sun and twilight sensor can be connected
- Cover frame and intermediate frame included
- Adaptable in switch ranges with 50 x 50 mm intermediate frame
- Colour: ultra white
- Made in Germany
Features:
Manual operation:
Manual control via up/down buttons
Automatic mode:
Daily programme:
One up and one down time programmable (repeats daily)
Weekly programme:
Different up and down times every day
Holiday programme:
Random generator shifts the switching times by ±15 minutes
Astro programme:
An astro time can be selected for each switching time. The pre-programmed geographical reference point for the astro programme is Frankfurt. A general astro shift of +/- 120 minutes can be set. If this is selected, all up/down times are shifted by the set value.
Sun/twilight programme:
Only possible with connected S/D sensor (accessory item: item no.: 607.S000.01). If the set sensitivity is exceeded for approx. 10 minutes, the roller shutter moves down to the sensor. If the value then falls below the set value for approx. 10 minutes, the roller shutter moves up again. In the twilight programme, the roller shutter only moves downwards if the programmed switching time is exceeded and the brightness falls below the set value for approx. 10 min.
You can find the right SD sensor here:
| Technical data: |
| Article no.: |
941.DCZA.00 |
| Supply voltage: |
230V / 50Hz |
| Switching voltage: |
250 V AC |
| Switching contact load |
3 A (cos phi=1) |
| Temperature range: |
+5°C to +45°C |
| Travelling time: |
2.5 minutes (maximum) |
| Switchover delay: |
at least 0.5 seconds |
| Speed accuracy: |
<5 seconds /day |
| Speed reserve: |
approx. 1 minute |
| Degree of protection: |
IP 20 |
| Protection class: |
II |
| Conformity: |
CE |
| Installation: |
into deep switch box (Ø 60mm / depth: 66mm) |
What's included:
- 1 pc. GEBA Rollotimer Astro including cover frame and intermediate frame, ultra white,
Item no. 941.DCZA.00
- Operating and connection instructions
Manufacturer/EU Responsible person
geba Handels- und Entwicklungsgesellschaft mbH
Wecostrasse 7-11
53783 Eitorf
Germany
Phone: +49 2243 8804 0
E-mail: mailbox@geba.net
Safety instructions for switching devices
Please read these important safety instructions before commissioning!
Incorrect installation and operation can cause serious personal injury and damage to property.
Failure to observe this user information, including all instructions and provisions, will invalidate the warranty.
If these instructions are not followed, the manufacturer or supplier shall not be liable for any personal injury or damage to property.
General safety instructions
Follow all instructions, as incorrect installation can lead to serious injury.
- Danger to life due to electric shock when working on electrical installations
.
- The electrical connection, installation and commissioning may only be carried out by qualified specialist personnel.
Assembly and connection must always be carried out in a de-energised state to avoid the risk of electric shock.Only use switching devices that are equipped with a minimum contact opening of 3 mm and have the up and down directions interlocked against each other.
- Installations in damp rooms may only be carried out in accordance with the applicable regulations (e.g. VDE 0100, Parts 701 and 702).
Store the switching device in a dry and safe place when not in use.Devices may only be serviced or repaired by qualified personnel. Unauthorised repairs can lead to damage and safety risks.In the event of replacement, ensure that only original or equivalent spare parts are used.
- Keep the instructions for future reference
.
Inappropriate use
- Do not use damaged devices. If the switching device is defective, it must no longer be used and must be replaced immediately.
Keep the devices away from children and ensure that they are only operated by authorised persons.
- Children must not play with the appliance.
If the appliance is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.Make sure that no moisture or other contaminants enter the devices to avoid short circuits and malfunctions.
Proper use
- Make sure that switching devices are suitable for use with tubular motors and comply with the technical specifications.
Timers must be correctly programmed to safely control the movement of shutters and minimise potential injury hazards
- Persons must be instructed with the correct operation.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Check regularly that the switching device is working properly.
Disposal instructions
Separate collection of old appliances
Electrical and electronic appliances that have become waste are referred to as old appliances. Owners of old appliances must dispose of them separately from unsorted municipal waste. In particular, old appliances do not belong in household waste, but in special collection and return systems.
Possibilities for returning old appliances
Owners of old appliances from private households can hand them in at the collection points of the public waste disposal authorities or at the take-back centres set up by manufacturers or distributors in accordance with the ElektroG.
Meaning of the "crossed-out wheelie bin" symbol
The crossed-out wheelie bin symbol regularly displayed on electrical and electronic appliances indicates that the appliance in question must be collected separately from unsorted municipal waste at the end of its service life.
